manufacturer category series package voltage class rev . date ecliptek corp. oscillator e15c7 ceramic 2.5v os1c 10/04 e15c7 series oscillator e15c7 electrical specifications 800-ecliptek www.ecliptek.com for latest revision specifications subject to change without notice. ? rohs compliant (pb-free) lvpecl output oscillators 2.5v supply voltage at-cut fundamental mode inverted mesa crystal ceramic 6-pad smd package stability to 25ppm tri-state output complementary output available on tape and reel wide range of available frequencies 0c to 70c, or -40c to +85c -55c to 125c 2.5v dc 5% 75ma maximum 100ppm, 50ppm, or 25ppm maximum v cc -1.025v dc minimum v cc -1.620v dc maximum 1 nseconds maximum 50 10(%) 50 5(%) 50 ohms into v cc -2.0v dc complementary output and tri-state enables output enables output disables output: high impedance 10a maximum 10 mseconds maximum 2 psec maximum 1 psec maximum 3 psec typical, 5 psec maximum -60dbc/hz at 10hz offset -95dbc/hz at 100hz offset -124dbc/hz at 1khz offset -143dbc/hz at 10khz offset nominal frequency operating temperature range storage temperature range supply voltage (v cc ) input current frequency tolerance / stability output voltage logic high (v oh ) output voltage logic low (v ol ) rise time / fall time duty cycle load drive capability logic control / additional output tri-state input voltage standby current start up time rms phase jitter rms period jitter typical phase noise inclusive of all conditions: calibration tolerance at 25c, frequency stability over the operating temperature range, supply voltage change, output load change, 1st year aging at 25c, shock, and vibration 20% to 80% of waveform at 50% of waveform v ih of 70% of v cc minimum no connection v il of 30% of v cc maximum without load < 77.760mhz fj = 12khz to 20mhz > 77.760mhz fj = 12khz to 20mhz fo=155.520mhz h 2.0 l 7.0 w 5.0 38.880mhz to 77.760mhz, and 78.125mhz, 80 mhz, 80.157mhz, 85mhz, 87.125mhz, 90mhz, 100mhz, 106.25mhz, 110mhz, 119mhz, 120mhz, 122.888mhz, 124.4mhz, 125mhz, 127mhz, 128mhz, 133mhz, 133.333mhz, 137.472mhz, 150mhz, 155.52m, 156.25mhz
line 1: ecliptek line 2: xx.xxx m frequency in mhz (5 digits maximum + decimal) line 3: xx y zz week of year last digit of year ecliptek manufacturing identifier manufacturer category series package voltage class rev . date ecliptek corp. oscillator e15c7 ceramic 2.5v os1c 10/04 mechanical dimensions all dimensions in millimeters environmental/mechanical specifications marking specifications tape and reel dimensions all dimensions in millimeters suggested solder pad layout all dimensions in millimeters 800-ecliptek www.ecliptek.com for latest revision specifications subject to change without notice. e15c7 e 2 f - 155.520m tr part numbering guide available options blank=tubes tr=tape and reel (standard) frequency logic control/additional output f=complementary output and tri-state duty cycle 1=50% 10%, 2=50% 5% frequency tolerance & stability/ operating temperature range c=100ppm maximum over 0c to +70c d=50ppm maximum over 0c to +70c e=25ppm maximum over 0c to +70c g=100ppm maximum over -40c to +85c h=50ppm maximum over -40c to +85c j=25ppm maximum over -40c to +85c pin 1: tri-state pin 2: no connect pin 3: case ground pin 4: output pin 5: complementary output pin 6: supply voltage a b c d e f 16.3-.1 7.5.1 6.75.1 4 .1 2.1 f g h j k l 8.1 b0* 1.5 +.1-0 a0* .3 .05 k0* tape m n o p q 1.5 min 50 min 20.2 min 13.2 40 min r s t u v qty/reel 2.5 min 10 min 22.4 max 360 max 16.4+2-0 1,000 reel *compliant to eia 481a tolerances= +0.1 characteristic specification fine leak test mil-std-883, method 1014, condition a gross leak test mil-std-883, method 1014, condition c mechanical shock mil-std-202, method 213, condition c vibration mil-std-883, method 2007, condition a solderability mil-std-883, method 2002 temperature cycling mil-std-883, method 1010 resistance to soldering heat mil-std-202, method 210 resistance to solvents mil-std-202, method 215 pad termination information pad material description material thickness sub-metal nico sub-metal plating ni 1.27 - 8.89m outer-metal plating au 0.30 - 1.00m
|
